- Description
- Warranty Information
Package Includes: - (1) Power Acoustik MOFO-154X 15" 3000 Watt Car Audio Subwoofer DVC 4-Ohm Sub
- (1) Rockville dB13 3000 Watt Peak/750w RMS Mono 2 Ohm Amplifier Car Amp
- (1) Rockville RWK41 4 Gauge Complete Car Amp Wiring Installation Wire Kit with RCA's
- (1) Rockville RGS15 Single 15" Sealed Car Sub Enclosure Box 2.03 Cu Ft, 3/4" MDF
- (1) Complete Single Sub Box Enclosure Installation Kit: Speaker Wire, Screws, Spades
Description:
MOFO-X subwoofers are refined and increase efficiency dramatically! MOFO subs use a composite sandwich cone with a polypropylene surface for durability and Spruce pulp backing for smooth low bass. Like the original MOFOs, the new models still use an aluminum dust cap that couples to the voice coil former and extends over the cone. Why? The fins brace the cone and eliminate cone flex during high excursion. And since they are aluminum and couple to the voice coil, they act as a heatsink or heat extractor. Using the latest materials, the new MOFO subs yield superior performance. Cast aluminum baskets? Of course! Increased bottom octave output? You Bet! Louder than the original design? Duh!!
Cast Aluminum HeatsinkThe anodized blue dust cap on the MOFO subwoofer looks cool and also serves a specific purpose. Because the dust cap is coupled to an aluminum voice coil former, it acts as a heatsink, extracting heat away from the voice coil, keeping it cool.
Non-Pressed Pulp ConeAsk any sound quality enthusiast what woofer cone material they prefer, and they will all say PAPER. With that in mind, we used a beefy non-pressed pulp paper cone. The aluminum dust cap fits into the recesses of the cone for additional bracing.
Features:
- Overcompensating Motor Structure for Increased Magnetic Strength
- 12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics
- Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up
- Die-Cast Aluminum Heat Sink Dust Cap Absorbs Voice Coil Heat
- Aluminum Dust Cap Fins Dissipate Heat & Strengthen Cone
- Non-Magnetic Non-Resonate Die-Cast Aluminum Frame
- 2.5 4-Layer Voice Coil w/ Large Gauge Wire Increases Power
- High-Temperature Tolerance Adhesives Resist Thermal Failure
- Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
- Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection
- High-Density Polyether Foam Surround w/ UV & Chemical Protection
- Dual Poly-Cotton Suspension Dampen Violent Accelerations
- Stitched Voice Coil Leads Prevent Potential Damage
- 1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Included
Specifications:
- Max Power Handling: 3,000 Watts
- RMS Power Handling: 1,700 Watts
- Efficiency (1w/1m): 86.90
- Voice Coil Configuration: 2.50? Dual 4O
- Motor Volume: 373oz
- Mounting Depth: 8.125?
- Optimum Sealed Enclosure ft3: 2.00
- Optimum Ported Enclosure ft3: 4.00
Enclosure Recommendations
All enclosures should be made of .75 (3/4) material only. When possible, make the baffle 1.5 (1 1/2) thick and add .75 (3/4) to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out enclosure.
Sealed Enclosure
- Cubic Feet: 2.00
- Tuning Frequency: 40
Ported Enclosure
- Cubic Feet: 4.00
- Port Diameter: 4" x 11.75"
- Tuning Frequency: 35.6
Driver Parameters
- FS (Hz): 24.4
- QMS: 5.95
- VAS (ft3): 4.077
- X-MAX (mm): 15
- X-MECH (mm): 23
- QES: 0.51
- RE (O): 7.23
- BL (Tesla): 26.3
- RMS Power: 1,700
- MAX Power: 3,000
- QTS: 0.47
- SPL (1w/1m dB): 87
- Voice Coil: DVC 4O
Physical Dimensions
- Overall Diameter: 15.5"
- Overall Height: 9.25"
- Mounting Depth: 8.125"
- Cutout Diameter: 14.125"
- Motor Diameter: 7.875"
- Motor Height: 3.00
- Flange Width: 0.75
- Flange Height: .625"
- Weight: 30lbs.??
Video of dB13:
Description:
The dB13 is a mono amplifier with 3,000 watts peak output and 750 watts Dyno Certified power. Here at Rockville we offer the best value in car audio. We therefore want to make it easy for you to compare our products to any brands on the market. The peak rating can be used to compare with brands who use peak ratings such as Boss and Power Acoustik while the Dyno Certified RMS rating can be used to compare with top brands such as Kicker, Rockford, Alpine, etc.
One of the tricks to determine the real power of a car amplifier is to multiply the fuse rating by 10 to determine the true RMS power. This formula almost always works within 20 %. The dB13 features a Maxi fuse with a rating of 80 Amps. Although we rate these conservatively at 750 watts Dyno Certified @ 2 ohms, this amplifier puts out more power than this!
This amp has a fully adjustable 12dB/Octave crossover with differential circuitry. Other features include a subsonic filter, a fully adjustable bass equalizer, mute and delay soft start technology, a phase control switch, and a dashboard subwoofer control for added convenience. The dB13 is protected by a full IC controlled circuit and has professional peak limiter circuitry guaranteeing distortion free music playback at all levels.
The RCA input accepts both balanced and un-balanced inputs. If there is potential inference in the car, the balanced input signal is less susceptible to noise.
The dB amps by Rockville use the top parts and components recommended by Rockvilles very own engineer. These amps are the best sounding out of any series we have ever created. They perform more efficiently resulting in even dB of sound. We created them to be 2 ohm stable just like the worlds most famous amps by Rockford Fosgate, Kicker, etc. If you compare our amp to the most famous amps you will find our amp can compete and, in my opinion, surpass the performance of anything in its class.
Each and every amplifier we manufacture is tested twice. Once at the semi-finished PCB stage of production, and then another test is done at the final assembly. We also run age tests on them. After this is all done, we hire a 3rd party independent company unaffiliated with our factory or with us to go to the factory and inspect 20% of all the production items. We test the power, the controls, and over 20 other tests. We guarantee these amps will satisfy you. We are so confident in your satisfaction of this amplifier that we will offer you a 90 day money back guarantee. If this amp does not perform as well as you expected we will send you a pre-paid shipping label and give you all of your money back. This means if for any reason you want to return the amplifier back for a full refund within 90 days, you can! (Amp must be complete along with the box).
Includes:
- Amplifier
- Bass Remote
- Birth sheet with tested power
- Owners manual
- Mounting Screws
- Warranty
Features:
- Rockville dB13 3000 Watt Peak/750w Dyno-Certified RMS Mono 2 Ohm Amplifier Car Amp
- Dyno Certified RMS Power Ratings: (Certified Dyno Test / Less than 1 % THD) (Use these ratings when comparing with top brands such as Kicker, Rockford Fosgate, etc) - 2 Ohm: 750 Watts x 1 Channel <1% THD+N - 4 Ohm: 450 Watts x 1 Channel <1% THD+N
- Peak: (Use these ratings when comparing with the top budget brands such as Boss, Power Acoustik, etc) - 2 Ohm: 3000 Watts x 1 Channel - 4 Ohm: 1800 Watts x 1 Channel
- High-Speed MOSFET Power Supply
- Optical Coupler Class D Technology
- Fully Adjustable 12dB / Octave Crossover with Differential Circuitry
- Low Pass Filter: 50Hz - 250Hz
- Subsonic Filter: 15Hz - 55Hz
- Phase Control Switch
- Full IC-Controlled Protection Circuitry
- Remote Dashboard Subwoofer Control
- Fully Adjustable 12dB Bass Equalizer
- Mute and Delay Soft Start System
- RCA Preamp Line Output
- 8 Volt Preamp Circuitry
- Status Mode LED Indicator
- Minimum THD at Rated Power: <0.1%
- S / N Ratio: >90dB
- Under Voltage Protection at 10V
- Over Voltage Protection at 16V
- Frequency Response: 15Hz - 250Hz
- Damping Factor: >150 @ 100Hz
- 80 Amp Maxi Fuse
- Dimensions: (W x H x L) 9" x 2.4" x 14.7"
Video of RWK41:
Unboxing Video for RWK41:
Description:
The Rockville RWK41 4 AWG (American Wire Gauge) amp kit has the following differences over other amp kits on the market at this price point.
1. Our RCA cables are 100 % copper. These are top of the line RCA cables
2. Better Resistance: The only thing that really matters with wires is the resistance rating. This is a measurement of conductivity and how much signal is loss per foot of wire. Since Rockville wires are made with around 3 times as much copper as any other wire at this price point, these wires had a much better resistance rating which means they will transfer more power to your amps than the other brands.
3. We do not cheat you on the thickness of the wire. These are standard American wire gauge thickness. This is another reason our conductivity is better than anything else at this price point. Other brands in the market place write 4 gauge, but cheat you on the thickness. We are honest about the thickness.
4. The Rockville amplifier installation kits feature a new soft abrasion proof insulating jacket. This rugged PVC outer jacket allows for 100% improved flexibility over standard power cables making them extremely easy to route through your vehicles interior, and it maintains exceptional resistance to grease and oil. The PVC outer jacket can with-stand an extreme temperature range of -40 to 220 degrees F.
The RCA signal transfer cables included in this kit feature blue and silver twisted pair technology in a clear outer jacket insulation skin. Not only do the blue and silver wires look cool but they also provide superior signal transfer with maximum noise suppression. They are 100% copper to provide absolute lossless perfect signal transfer to your receiver. This technology reduces interference, so your audio signal flows clean and pure at all power levels.
This kit also includes a massive 60 Amp AGU Gold Plated Fuse, so you can be sure it will handle the all the DC power that your amp will need without even the slightest loss of current. The included 7 split loom tube provides protection for your power cable from the typically harsh environment found under the hood of your car.
Audiosavings product experts have tested this amp kit against many leading amp kits on the market and were were impressed not only by the great looks but by the quality of these Rockville installation kits as well. These kits had a lower resistance rating than the other brands we compared and tested them against. What this means is that Rockville manufactures their kits with more copper than other kits at this price point, ultimately providing your amplifiers with better and cleaner DC power, so they work cooler and more efficiently. You will hear the difference a Rockville installation kit will make!
Features:
- 1 17 High Grade Twisted Pair of 100% Copper RCA Cable
- 17 4 Gauge Translucent Blue SuperFlex Power Cables
- 17 18 Gauge Blue Remote Cable
- 17 16 Gauge Clear Speaker Wire
- 3 4 Gauge Clear SuperFlex Ground Wire
- Gold Plated AGU Heat Resistant Fuse Holder
- 60 Amp AGU Gold Plated Fuse
- 7 Split Tube Loom
- Accessories Included: Wire Ties, Ring Terminals, Butt Connectors, Spades, and Grommets
Description:
The RGS15 is a single sealed 15" speaker box is made in the USA with Grade A MDF wood. This enclosure is made with precision cutting machinery by industry experts that have been making these enclosures in the USA for over 20 years. All Rockville enclosures come with a customized enhanced glue that is unmatched by any other manufacturer. That means that the carpet will stay in place and not rip or tear. The USA MDF is much stronger then any type of import wood. This will keep your box performing at an optimal level by not flexing and distorting your woofers. Your woofers will thank you! EVERY Rockville enclosure is not only glued at all joints but stapled as well.If that wasnt enough we add a layer of silicon to every seam! This makes your Rockville enclosure rock even more!
MADE IN THE USA WITH PRIDE!
Features:
- Rockville RGS15 Single 15" Sealed Subwoofer Enclosure
- Proudly Made In The USA, Using Only The Finest Quality Materials - For The Best Level of Performance From Your Subs!
- 3/4" USA Heavy Duty MDF Construction
- Machine precision cut mounting holes
- Top of the line Glue for extra durable adhesion
- High quality GOLD spring loaded terminals
- Designed, tested, and engineered to work with most of todays popular woofers.These enclosures are built with the quality additives needed to maximize the performance of any sound system.
Enclosure Measurements:
- Type of Enclosure: Sealed
- Enclosure Sub Size: Single 15"
- Dimensions in Inches: 16" L x 18" W x 16.25H"
- Top and Bottom Depth: 17"
- Mounting Depth: up to 14.5" (enough depth for any sub on the market)
- Gross Volume Per Sub (Measurement for the outer dimensions of the box): 2.70 Cubic Feet
- Net Volume Per Sub (Measurement for the outer dimensions of the box less the thickness of the wood): 2.03 Cubic Feet
About Rockville Quality Control Procedures:
The Rockville brand stands for Quality, Innovation and Value. All Rockville products go through the most rigorous quality control standards in the industry. Products go through months of extensive testing before they reach your hands. All user functions are tested and all internal components are tested for quality. Rockville makes products that are virtually un-breakable! Rockville is one of the only brands in its class to test every concept model for weeks or months before starting production. Once production begins, Rockville sends product engineers to their factory to quality control every line of production. During production every product is tested and on top of that Rockville goes the extra mile and has their high level product engineers do an additional quality control. They test a certain percentage of all products from the production line a second time to ensure that the quality meets their vigorous standards, and to make sure that there is never a batch of products with even a slight problem. All Rockville sub enclosures are backed with a full 90 day warranty, though it is unlikely that you will need to use it.Complete Single Subwoofer Enclosure Installation Kit!
Includes:
- 10 Drywall Wood Screws (Wood screws are the type of screws; the screws are actually made of metal)
- 12 Feet of 14 AWG Blue Speaker Wire
- 2 Spade Terminals
This accessory package includes everything you need to install one subwoofer into an enclosure, and wire to connect the enclosure to your amplifier. This package is a top of the line accessory package which we put together and tested.
The drywall wood screws were hand selected by our installation experts because they drill into the enclosure very cleanly, without chipping the enclosure. The speaker wire is 14 gauge. This is way better than using 16 gauge. You can be 100 % sure that your enclosure will have a clean signal to the amplifier with this top of the line speaker wire. These spade terminals have also been hand selected by our installation experts to make the internal wiring simple, secure, and to run the audio signal cleanly.
1 YEAR
